The 10 Scariest Things About Glass Window Repair

Glass Window Repair

Professional window repairmen are able to maneuver large glass panes from a height higher than the ground. They adhere to strict safety standards and often work under extreme weather conditions.

Wearing protective clothing, remove all glazing putty and metal glazing points using a utility knife. A heat gun may help soften the old glue and make it easier to remove.

Replacement

When a window pane breaks, it could be tempting to repair the glass instead of replace it. However, replacing windows is usually more cost-effective and can help prevent other problems in your home's energy efficiency. Examine the type of glass that is broken to determine if it's a temporary fix or if a long-term solution is required.

To repair a broken window, take off the frame or sash and lay it flat on the floor. Wearing eye protection, gently wiggle the window's frame and then remove any remaining fragments. Then, use a knife to peel off the glazing compound and glazing points that help to hold the glass in the position. Keep track of the components and their location so they can be reinstalled.

After the frame and sash are removed then you can begin the process of preparing to install the new glass. Make sure that the opening of the frame is the right size for your replacement window. Take measurements both ways across the opening, then subtract 1/8 inch from each measurement in order to leave space for expansion and contraction of the frame and glass. Then, buy double-strength glass cut to these exact measurements. It is also an excellent idea to buy enough new glazier's glazier's pointing or clips to be installed every 6 inches around the window pane.

Based on the window's warranty, this may be covered by the manufacturer, in which case you need to contact the company to file a claim. After the new glass has been put in place it is essential to cover it with a thin layer of glaziers compound. After the compound has dried then you can paint it to match the frame of the window.

If your crack is longer than an inch in length, you can prevent it from spreading by scoring a small arc just beyond the crack. This trick won't be infallible, but it will slow the development of the crack to a manageable amount until you can take more permanent measures.

Repair

Professional window installers know how to handle various kinds of glass and have the tools necessary to do the job correctly. They also understand the best practices for disposing of garbage, which means they're less likely to leave scraps in the trash, which could injure family members or pets. They are also experienced in working with various types of windows and could be able spot problems that a home owner with no experience would not notice.

Before beginning the process of fixing cracked window glass, installers be sure to wear safety glasses and gloves. Even a small crack can cause glass shards to fly around and put anyone at risk inside or around the house. It's also important to figure out what caused the crack in the first place, so that it could help avoid future issues.

Make a two-part mix of epoxy. They usually consist of composed of a 50/50 blend of hardener and resin. They must be mixed quickly. Once the mixture has been prepared and applied, simply apply it to the crack and allow it to dry. It will take just a few minutes however it is important to get it done quickly as the mixture is extremely thick and quick drying.

After the epoxy has dried, you can get rid of any excess using a putty knife. You'll need to clean around the cracked glass. If you don't clean the area properly, the debris could cause further damage to the glass. Make use of a putty knife to smooth the compound around the window's edge and match it to the frame made of wood.

To make a more durable option you can consider using a plastic covering. A heavy-duty trash bag or tarp is the best option, but you can also use masking tape to cover the glass. This will prevent the crack from spreading and will also keep wind, water and insects out.

If you're not able to get to the window in a timely manner and you're not able to get there quickly, you can use silicone sealant to create temporary repairs. Apply a small amount of silicone sealant to the edge of the damaged glass. It won't close the gap between the glass and the frame completely, but it will hold the broken piece in place until you can repair it.

Repainting

If your glass windows are old, you may want to repaint them. This is a cost-effective alternative to replacing windows, and can give your home a new appearance. Before painting, ensure that the surface is clean. Use rubbing alcohol or soap and water to wash away oil smudges and other traces of dirt that can hinder paint from adhering. You should also wear rubber gloves while working on glass to prevent the transfer of your own oils onto the glass surface. Apply multiple thin coats instead of one thick coat. This will make the paint last longer, and will keep your windows looking even and smooth.

Make sure you have the appropriate tools available in case you want to paint glass windows. You'll need a brush or sponge, painter's tape, toothpicks, a ruler and other tools, such as a rag or paper towel. You'll also need the brushes and paint you'll be using to complete the project. Follow the instructions of the manufacturer. Have patience, as it may take some time for the paint to fully dry.

If you're using solvent-based paint, also ensure that the room in which you work is well-ventilated. This will reduce the risk of breathing toxic chemicals, and the paint will dry faster. Use a mask that is protective when using spray paints.

It is necessary to clean the glass window thoroughly using soap and warm water before you paint it. Make use of soap and warm water to thoroughly clean the glass window. Then, use rubbing alcohol on any grease or oil residues that could interfere with the paint's adhesion. Make sure that the windows are completely dry before you begin painting them.

If you have energy-efficient double pane windows on your windows, it could be possible to make an insurance claim for repair or replacement with the window company or dealer that sold the windows. This is especially the case if you've experienced multiple problems with cracked glass or condensation even though the windows are covered under warranty.

Sealing

There are a variety of options to fix the problem, whether you have an old double-pane window with cracks in the seal, or if you have an insulated unit (IGU) that has experienced fogging. The most expensive option is to replace the frame and insulated unit however it could be required if fog or condensation are causing energy loss. Other options include replacing the IGU with a single pane, or repairing the existing IGU by drilling a hole in its bottom and filling it up with an anti-fogging agent.

You can also seal up the gap between a window frame and a sill or threshold using a felt strip or vinyl V-strip. Felt can be stapled, glued or nailed into place but doesn't offer much protection against moisture. Vinyl v-strip is easy to install and durable however it can be expensive. It is generally used in areas that are exposed to abrasions that are high. Door sweeps can be easily nailed to the floor and are affordable. However, they offer very little or no protection between the threshold and air.

To fix a damaged window seal make use of a putty blade to scrape off the caulk. Wearing eye protection and gloves remove the glazing point -- tiny fasteners with sharp pointed tips that hold the glass into the frame's recess. After getting rid of the glazing points remove the grooves, then sand the wood. Clean any sanding dust, then seal the bare wooden surface with a linseed-oil-based paint or clear sealer.

Traditional glazing putty can be applied with either a putty knife or a caulking gun. However, the knife is a better precision and precise application. It also creates a better seal. Choose a putty that is specifically designed for glass windows, as it has better adhesion and durability.

Apply a small amount the putty to the inside edge of the frame where it meets the glass. Slide the window into frame so that the scribed line on the glass is aligned with edge of frame. Apply pressure to the glass to force the putty and create an elongated seal. Smooth the compound with an ungloved finger and clean up any caulk that was applied incorrectly or errant drips before it dries.