Broken Car Key Repair: What No One Has Discussed

How to Do Snapped Car Key Repair

A damaged car key is a source of frustration, Auto Keys R Us whether you're trying open your car's door or start your engine. There are many ways to fix the problem that are more straightforward than others.

The first thing that most people do is look for the needle-nose pliers to try jiggling out the broken piece. This technique can work in the case of a piece that is close to the lock, or even higher in the cylinder. However, it is not always successful.

1. Super Glue

Super glue can be used to fix damaged car keys. You need to make sure that the break is clean and that the two pieces are able to fit together as tightly as is possible. Put a small amount super glue on the crack and then hold the pieces until glue is dry.

Make sure you select a wire or nail that is thin enough to fit between the damaged pieces. Cut the wire or nail to the length that is needed to connect the two ends of the key. After you've done that you can apply a small amount of super glue to the wire or nail and then insert it into the gap between the two broken ends of the key.

After the glue has dried you should be able to use your new car key. Be sure to test the key in the ignition to make sure that it works as intended. If you're unable to get the key to work, you should go to a locksmith or dealer for a replacement.

2. Pliers

Superglue is the first thing one would use to fix a damaged car key. However, this isn't the best idea. Glue and keys don't mix well even if the glue does hold the two pieces together, it could fail when you insert the key into your ignition lock. Then, you'll have to replace the key and the lock cylinder. This is an expensive process.

One option is using pliers to remove the broken pieces. If there is enough of the key sticking out to be snagged with needle-nosepliers, you will be able to pull it out. This is a risky procedure because it can cause the broken pieces to twist and then become stuck in the lock or ignition.

Use tools that are thin, flat and have hooks that are small. They can slide through the gap and hook onto the teeth of a damaged key, which can then be pulled out. You can also purchase a fluid that sprays into the lock and assist the tool work its way into the gap.

3. Removal Tools

Car keys that snap in ignitions or door locks are a hassle to remove. If the damaged part is partially exposed it may be possible to grip and take it out. If the key is totally broken or snapped, you will need an auto keys r us locksmith to remove it.

There are tools available to aid you in wedgeing the key and then pull it out. Key extractors can be found at hardware stores as well as in the automotive sections of a lot of big-box retailers.

Another simple tool for removing broken bits is a pair of needle-nose pliers. They slide into the ignition keyway and grab the broken piece when you remove it. This process requires patience, as you may need to test it multiple times before applying lubricant. Alternatively, Auto Keys R Us you can use mini hacksaw blades available in the hardware section in some large-box stores. These can be used much similar to needle-nose pliers but must be handled very carefully to avoid damaging the ignition.

4. Lock Picks

A lock pick is an extremely thin piece of steel with an angled tip. It can be used to manipulate the inner parts of a lock mechanism (pins). There are various kinds of lockpicks including hooks and rakes. Lock picking requires lots of practice. It is important to know how much pressure to apply and where to place the pins and how to use each type of pick.

If you do not have a lockpick, you can try using a small wire. Paperclips can work if it's straight and long enough to fit into the keyhole opening. You can also make use of two pliers specifically those with narrow jaws.

Spray WD-40 or any other penetrating oil into the lock to aid in making it lubricate. Then, place the broken car key fragment to lock or unlocked position. Then, insert the tip of your extractor tool into the open space in the keyway and apply the plug with torque by turning it gently. This will allow you to extract your broken key fragment by setting the pins one at a time within the lock.

5. Dealership

If there is no enough of your broken key to to grab it with pliers, you will need to get a new one made. It is possible to do this through a dealership or locksmith, but bringing the old key can save you money.

Dealerships are able to offer the best prices, but it could take longer to create keys. Their technicians may also be unable to find the right blanks for your particular vehicle particularly if it's an older model that requires keys that have transponder chips.

A dealership can use keys that have been damaged by a car in a variety of ways. They can duplicate the key if there's a substantial amount of blade sticking out. You will receive a replacement key. This is cheaper than buying a new one since they don't have to pay for a code to cut the blade replacement. This can save a lot of money. The only drawback is that you won't have an additional spare.