10 Facts About Fiat Panda Key Fob Replacement That Can Instantly Put You In The Best Mood

Reasons Your Fiat 500 Key Fob Won't Work

A Fiat 500 key fob makes it simple to open doors and start your vehicle. There are a variety of reasons why the fob could stop working. This includes a dead coin-battery, water damage, issues with the receiver module, and interference.

This listing is for an NEW replacement fiat ducato remote key programming (click through the up coming website) Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob being inoperative. Modern key fobs have a very restricted operating range, and should be within just a few feet of the vehicle in order to function. If you are far from your vehicle when you press the key fob button the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) with a new battery from a reputable brand such as Panasonic Duracell or Energizer. You can typically find them in your local hardware store, or online.

You can test the battery on your coin-cell by pressing the buttons while standing close to your Fiat 500. The car should blink its parking lights and the key fob should be able to operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it could have water damage that stops it from communicating with the receiver module in your car. Water damage can occur in a variety of ways, from the slightest splash to submerging the fob salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If this doesn't work your fob will probably need to be reset by a professional auto locksmith or by the dealer.

Water Damage

Although the fob is equipped with rubber seals to keep water from the chip's electronic circuit the device, submerging it into the ocean or fiat ducato remote key programming washing it in a machine could cause water damage. Saltwater can cause the circuit board to short, and eventually fail. The fob getting wet is not an ideal choice but if you accidentally drop it into the water in a cup or do not remember to remove it from your pocket before you run the washing machine do not give up hope.

First remove the battery from the fob. Before replacing the battery, clean the electronic chip using isopropyl or another similar product. Then check the fob to check if it functions. If the key still doesn't work, it may need to be programmed again. This is usually done by a dealer or professional auto locksmith.

If the key is a newer model and was not programmed to your vehicle, it will likely need to be replaced completely. A professional locksmith for cars will be able to complete this process. The locksmith will require the key to be cut to match your vehicle's ignition. The locksmith will also need to reprogram the fob into the vehicle's system. This is a cost-effective and quick process that could be completed within the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob could stop functioning is because it's out of range. The remote has a maximum range of 30 feet. So when you're too far from your vehicle it won't respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding.

If you've replaced the battery on your coin (commonly known as a "button" or "watch") and the fob isn't working it could be due to an internal circuit board problem. In the majority of cases, reprogramming your fob will resolve this issue. You can find instructions on how to do this for all vehicles by searching YouTube or consulting the owner's manual.

It's possible that you need to replace the metal clips that keep the coin battery in place. If they lose tension, it can prevent the coin battery from being properly seated, and this will cause your remote to malfunction.

In rare instances the fob might become desync'd with your vehicle due to software issues or hardware issues. This can cause a major trouble, but you could usually fix it by visiting an auto locksmith to have them reprogram fiat 500 key fob your fob. In some cases the software may need to be reinstalled in your body control modules.

Interference

In addition to a dead battery on a coin The key fob may not be receiving or transmitting an signal due to interference. This can occur when the key fob is in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob might not work because of a weak connection to the buttons, water damage or damage to the internal chips.

If the key fob failed to work one day out of the blue, or after trying every option at home to solve it e.g. You could have a malfunctioning 500 receiver module if you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, picks up radio frequency signals from your key for fiat 500 fob. It converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's internal system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Then, reconnect the battery. This will eliminate any residual electricity and restart the car's computers, which can help get your key fob working again. If the problem persists you should speak with an expert technician. They will be able to diagnose the exact cause of your problem.